OSB roof panels should always be installed with the grade stamp facing into the attic and the screened surface (with the nail guide lines) facing up. When the grade stamp is covered by roofing, the building inspector will not be able to confirm that the correct OSB roofing panel was used..
Herein, can you use OSB on a roof?
Both OSB and plywood panels can cut and installed on a roof using conventional roofing equipment. They have similar structural characteristics, and can be used interchangeably. OSB is now the most-used sheathing and subflooring material for new roofs and roof replacements.
what side of OSB goes down? "This side down" applies to when it's used as subflooring. That side should be facing down, against the joists. When used as wall sheathing, that side should be against the studs.
Keeping this in consideration, what thickness OSB should be used for roofing?
Typical types of wood used for roof sheathing are oriented strand board, known as OSB, and plywood, the most popular being OSB. Sheets of 7/16-inch thick, with no edge support, can be used in an area where the snow load is 30 pounds per square foot. With edge support and the same snow load, 3/8-inch OSB can be used.
Can I use OSB for shed roof?
OSB is fine all the way around. Good enough for houses, good enough for a shed. The OSB thickness will be based on the rafter spacing. 7/16 will be fine for 16" on center, and 5/8 for 24" on center rafters.
Related Question Answers
Can I use screws for roof sheathing?
Screws can be used for even greater withdrawal strength, but should be sized by the building designer. Staples are not recommended for roof sheathing attachment in high-wind areas. It is extremely important to have proper fastener spacing on all panels.What is stronger OSB or plywood?
Osb is stronger than plywood in shear. Shear values, through its thickness, are about 2 times greater than plywood. This is one of the reasons osb is used for webs of wooden I-joists. However, nail-holding ability controls performance in shear wall applications.What kind of nails do you use for roof sheathing?
Fasten panels with a minimum of 8d Common (0.131-inch by 2-1/2-inch) nails spaced a maximum of 6 inches on center at supported panel ends and edges. At intermediate supports, fasten panels 12 inches on center. In high-wind areas, more fasteners may be required.Is OSB better than plywood for roofing?
OSB takes longer to get wet than plywood but also takes longer to dry out. When used as a roof sheathing, this tendency to hold moisture means it can degrade faster than plywood when exposed to chronic leaks. Swollen edges have been known to telegraph visible ridges called “ghost lines” through asphalt roof shingles.Should roof sheathing have gaps?
Sometimes, plywood or OSB was installed right on top of the boards. The recommended maximum gap between roof sheathing boards for low-quality, 3-tab shingles is 1/4-inch. If asphalt shingles are installed over sheathing with gaps exceeding 1/4-inch, over time, these gaps may telegraph through and become visible.What side of OSB Do you paint?
Will I still be able to paint it? For interior uses the OSB should be smooth side out. The reason it is textured on one side is for roofing purposes and states to install with that side up. You put a smooth side up on a roof and you are going ice skating.How do you seal OSB?
Soak the tip of your paintbrush in your sealer and begin brushing it over the surface and on the ends of the OSB pieces. Make sure you repeat this process on each side, not just where your cuts were made. Coat the pieces as they lay on the tarp, and then let the waterproofing sit to dry for 12 to 14 hours.Is OSB cheaper than plywood?
OSB is cheaper than plywood by about $3 to $5 per panel. For a typical 2,400 sq. ft. home, OSB is about $700 less expensive compared with plywood if used as the subfloor, sheathing, and roof decking.How much weight can 3/4 OSB support?
Medium OSB Panels of OSB that are 23/32- and 3/4-inch-thick, set on joists 24 inches OC, can bear 100 psi live weight and 10 psi dead weight. Panels that are 7/8-inch and 1-inch-thick, mounted on joists 32 inches OC, can bear 100 psi live weight and 10 psi dead weight.Can you waterproof OSB?
OSB is strong and water-resistant. Every single fiber or piece of wood in an OSB is saturated with a cocktail of resins designed to provide superior strength and waterproofing to the finished product. This type of board is an excellent material for use in waterproofing systems, be they roof, sub-floor or wall.How much does a sheet of OSB cost?
OSB (Oriented Strand Board) Prices The low price point has given OSB an edge in popularity over T1-11. A sheet of this composite sells for around $5 less than its counterpart, with a cost between $15 and $43 per sheet depending on thickness. Like plywood, OSB describes engineered lumber.Is 7/16 OSB OK for roofing?
Wall panels 7/16 Category may be used on studs spaced up to 24” o.c. LP OSB sheathing panels are designed for use in roof, wall and subfloor systems in commercial and residential projects, maintenance, remodeling or new construction. OSB sheathing panels comply with the following industry standards and certifications.What is the best material for roof sheathing?
The two most popular roof sheathing materials are OSB and plywood. Both of these are more economical than radiant barrier roof sheathing and zip system roof sheathing. Because of their affordability, most homeowners opt for one or the other. However, there is some debate as to which material is the best.Can you put plywood over old shingles?
The existing asphalt shingles need replacement, so he plans to do a tear-off and re-shingle. Because the plywood roof sheathing under the shingles has become brittle and weak, he plans to install new plywood as well as new shingles. The new plywood will have to be nailed to the rafters or roof trusses.Do I need plywood under metal roof?
While metal roofing doesn't require plywood underlayment, there are circumstances in which you may wish to install plywood to anticipate future roofing needs or to offer additional soundproofing. Modern metal roofs are expected to last 30 years or longer.What is the best thickness for roof sheathing?
Most Common Thickness For rafters spaced 20 or more inches apart, 1/2- or 5/8-inch plywood is recommended. The most common rafter spacing is 24 inches, and 5/8-inch plywood is recommended for that. It will support roof loads for most situations and is the standard for most roof applications.Can OSB board be used outside?
Oriented strand board (OSB) is far superior to particle board for exterior use. Even the old type OSB used as a substitute for plywood is decent in exterior applications, although it will absorb water if exposed.Can OSB get wet during construction?
Allowing OSB to get wet is not a wonderful idea but its done all the time. Most of the time there is very little harm and the material doesn't loose strength or any of its integrity. OSB that does get wet will tend to swell and delaminate first at the edges of the boards.Is 11mm OSB OK for shed roof?
For heavy duty roofing, you may want to opt for an 11mm tongue and groove roof, additional roof trusses can offer even more support for your shed roof. For an inexpensive, value option 9mm OSB can be used for your garden shed roof. 
